The loss of dryer duct functionality can be heartbreaking for someone used to warm towels directly from the dryer and smooth, wrinkle-free clothes. Whatever is malfunctioning with your dryer has something to do with the belt fan or the heat mechanisms. However, there are times when a dryer stops heating or circulation of air because the vent duct stops venting. Vent ducts might be crushed, tangled, shredded, or blocked with dryer lint. It makes it impossible for them to provide the free airflow and moisture release that every dryer requires. If your dryer’s troubles aren’t mechanical or internal, the vent duct is most likely to blame.
A dryer vent is a relatively simple and uncomplicated appliance to replace yourself. Before buying tools, remember that the smoother and less restrictive the vent tube run is, the sooner your garments will dry. The dryer will work less, and your clothes will be less worn due to the shorter working duration. Also, because lint build-up can cause safety hazards, you should install a dry vent to clean out the lint.
If you’re merely attaching a new dryer to an existing venting in the same area as the old one. It may be as simple as connecting the new machine to the existing venting. However, if you’re installing a new vent, you’ll need to put in a little more effort and forethought.
Assemble your tools
You’ll require a few key tools to complete each step before you start replacing your dryer vent duct. Fortunately, the supplies list for this replacement isn’t too large or complicated. All you require is:
- Screwdriver
- Washcloth
- Drain Snake
Empty and clean the lint trap
After you’ve gathered your tools, you may begin working on the dryer. Begin by removing the lint trap filter from the top or just inside the machine’s entrance. The lint trap connects directly to the vent duct and, if clogged with lint, can reduce your dryer’s performance and durability. Don’t just pick up the extra lint for this process. You can also contact mold air duct cleaning Atlanta for assistance.
Allow some time to thoroughly clean the lint trap by soaking it in cool water and drying it with a rag. Now is also an excellent time to scoop out any leftover chunks of lint inside the lint trap housing, visible and reachable.
Remove the dryer from the wall.
Take your dryer away from the wall. Considering the state of your vent duct, this could even be a repair procedure in and of itself. Dryer vent ducts are typically crinkly foil tubes extending from the dryer’s rear to the exterior wall where the dryer outtake is located.
If your dryer is too deep, it might destroy the vent tubing, resulting in a tear in the vent or excessive linty air compression behind the dryer. Pulling the dryer away from the wall offers the dual benefit of unclogging a clogged vent and providing extra space to operate on the dryer from this point forward safely. Also, when you’re back there, make sure to disconnect your dryer.
Look for rips and gaps in the ductwork.
Give a thorough examination now that the vent duct is exposed. Look for any noticeable tears or damage that could be the source of the issue. Check for any small air leaks that could be causing vent inefficiency. These parts are one of the dryer’s most disposable features, and they should be updated regularly. You can also contact air duct repair and replacement Atlanta for more information.
If the damage is small, you may not need to replace the entire vent duct. This is precisely the kind of problem that duct tape was designed to solve. A few pieces of duct tape applied to a rip in your vent duct can make it airtight and even more durable than before in terms of preventing collapsing and potential damages.
Seal both ends of the duct tightly
Make sure that the seals on both ends of your dryer vent duct are intact. Even if the duct is completely intact, using a too loosely linked duct will cause you to lose hot air and dryer performance. Air leaks through the loose seals is terrible for your dryer, your clothes, and your electricity costs. Naturally, the remedy is to properly re-secure the duct seals before tightening them to ensure that they do not come free again. An effective dryer performance depends on a tight duct seal.
Replacing a Damaged Duct
If fixing and adjusting your dryer vent duct doesn’t solve the problem and you can still feel air coming out, the existing duct may be beyond repair. If this is the case, you’ll need to thoroughly investigate the duct required for your dryer’s make and model. Once you have the information, purchase a new dryer vent duct. It will most likely include the necessary connection pieces if they were lost or broken.
Remove the old dryer vent duct and carefully replace it with the new one. Make sure to tighten the vent duct screws on both sides so that your duct stays in its position while creating a tight heated air seal.
Also Read: 6 Most Leading Open Source Mobile App Development Software For 2022
